Knowledgebase : VeCOAX General Q/A
If you cannot receive on one TV, follow this procedure: 1) Make sure the Modulator is set as per the manual ( Reset to default ) 2) Connect a TV Direct to the Modulator with a short piece of cable 3) Turn on the modulator and scan / find the modulator...
I SEE THE PVI COLOR BARS / LOGO BUT NOT MY VIDEO SOURCE Television sets can receive from the Coaxial Cable VIA THEIR DIGITAL TUNER The TV digital tuner is set by FCC / EBU to receive NTSC / PAL signals ( 59.94 frames per second / 50 frames per second )...
For Combining ATSC (Over the Air channels) you must find the frequencies that are used by your local stations. This information can usually be found online by searching for, "(insert your local area) ATSC frequency chart." This will give you a nice ta...
Major / Minor channel numbers ( also called VCT virtual channel table ) are the DESTINATION POSITION on your TV CHANNEL LIST for each of your VeCOAX channel If you set MAJOR = 1 MINOR = 1 on your VeCOAX for a specific channel, that will show on your TV w...
You can contact your local service provider of your basic cable to find the frequencies that they use and fine the ones that are available for you to use. If you wish to inject into a Digital Cable Converter box or STB (set-top box) most of the time the...
Lines/Noise Across Screen in 1080p 60 requires high bandwidth cables If you see Lines or pixels noise across the screen there might be a loss of data on your hdmi cable or on your video source negotiation to work in 1080p mode Solution1 > Set your vide...
I AM LOOSING OTHER CHANNELS IN MY COAX NETWORK WHEN I TURN ON THE UNIT Check to ensure you are not broadcasting on the same frequency as other signals. Please refer to our, "COMBINING SERVICE PROVIDERS SIGNALS OR ATSC WITH YOUR DEVICE ," guide in the mini...
For Combining ATSC (Over the Air channels) you must find the frequencies that are used by your local stations. This information can usually be found online by searching for, "(insert your local area) ATSC frequency chart." This will give you a nice table ...
If you're having issues with the Quality of the Audio, please ensure your HDMI Source AUDIO IS SET >> TO >> STEREO LINEAR PCM FOR THE MINIMOD 2 / MIRCOMOD 3 YOU CAN TRY THE FOLLOW: 1) advanced menu > EDID > change to 1080i and save - then disconn...
My Camera DVR is not recognized with your unit Please set your Camera Recording DVR output resolution to a fixed 1920 X 1080 60Hz or 1280 X 720 60 Hz or 1080P/720P Depending on your model. Please refer to your DVR Manual Tags: Camera DVR Surveillanc...
MY SDI TO HDMI DOES NOT WORK WITH MY UNIT try another SDI > TO > HDMI converter the actual one might not propagate the resolution EDID from the SDI to the HDMI output HDMI requires the EDID to be properly formatted so the encoder can " understand " whi...
Analog-only Television, monitors, projectors can be converted to digital-tuner capable by simply using an external tv set top box These are decoders with remote control that outputs RCA and HDMI to your TV from a digital antenna / cable signal Find AT...
MY MINIMOD 2 OR MIRCOMOD 3 VIDEO IS NOT PLAYING ON MY TV Please check all connections, Units Settings, Correct TV Standard is set for your TV. Ensure your video source is working or Set to a Correct Fixed Resolution. Please refer to your HDMI source...
No Audio Please make sure you are connecting directly the hdmi video source to our device, so the EDID from our device can properly set the source to provide the correct audio. If you use an HDMI splitter to feed our device and other devices, make sur...
MY SCREEN GOES BLANK/ VIDEO DISAPPEARS WHEN I CHANGE THE CHANNEL OF MY SERVICE PROVIDERS CABLE BOX This is a common issue with the STB Cable boxes from your Cable Providers such as Xfinity Comcast, Spectrum, Shaw, DirecTV, Dish and many more. An...
In order to watch your vecoax channels on comcast boxes you must obtain from comcast the information about 1) channel ( frequency ) to use to watch your modulator > set on our modulator 2) service numbers ( hexadecimal values ) > set on our service id...
On your unit there are TWO RF COAXIAL connectors RF OUT > is the output you inject to your TV Coaxial Distribution ( connects to your wall tv socket / to your tv distribution box / to your coaxial splitter ) RF IN > is an ATTENUATED port typically use...
QAM 64 is the STANDARD-USED MODE when you use SINGLE CHANNEL VIDEO MODULATORS as the bandwidth is more than 25 megabit/s more than enough for broadcast video quality The QAM-64 is also very robust and not affected by cables, connectors, signal attenuatio...
You can plug your HDMI source cable into the Port labeled HD on the side of the unit where the power plugs into.